Richmond RCSupplyStore LogoZapGlue Logo
Checkout

PART NUMBER

VMA-P240A  Australian RAAF Roulette Demonstration Aerobatics Team

VMA-P240S  Swiss Version
Please note: graphics and photos shown depict the Australian Version unless specifically denoted "Swiss Version".

HISTORICAL INFO

- First Introduced

2001 01 01

- Availability Status

Booking for April 2001

- Supercedes

Brand New Release

- Superceded by

Brand New Release
- Change Log Highlights Click Here

RECOMMENDED FOR

Intermediate. Great for Sport Scale. Officially classed as Semi-Scale with unbelievable resemblance and detailing to match the real thing.

HOURS TO FINISH

Eight

INDEX to DETAILED INFORMATION

WING

- Location on Fuselage

Below Fuselage

- Span

57-3/4 in. (1467 mm)

- Area*

540 sq in. (3484 sq cm)

- Airfoil

Symmetrical

- Taper

Yes. Leading and Trailing Edge Taper

- Chord Size

Root = 10-3/8 (264 mm). Tip =  7-7/8 in. (200 mm) 

- Thickness

1-3/4in. (44 mm)

- Construction

Wood - Built Up

- Aileron Type

Strip with pre-installed torque rods

- Ailerons Pre-Hinged?

Yes. 4 Hinges per Aileron

- Hinges Factory Pinned? Yes. 4 pins per inboard & outboard hinge. 2 pins per centre hinge.. 

- Hinge Type

Real Hinge with Metal Pin

- Flap Type na
- Flaps Pre-Hinged? na
- Flaps Factory Pinned? na

- How Joined?

Wood Dihedral Spar Joiner & 2 Wood Alignment Pins

- How Mount to Fuse?

2 Fixed Dowels in leading edge of wing and 2 Nylon Bolts near trailing edge.

- Servo for Wing?

Yes only 1 needed.

- Servo Location

Top centre of Wing.

- Second Wing Servo

Not required and not specifically provided for. A second servo can be fitted with minor modifications to wing skin

- Color Top

Red and white with blue trim, black lettering & gray rivets & panel lines. 

- Color Bottom

Red and white with blue trim & gray rivets & panel lines. 

- Color Pattern Top vs Bottom

Very Similar

- Picture of Wing Top and Bottom. 

 

Blowup of wing graphic detailing with panel lines and rivets.

More Pictures of Wing

FUSELAGE

- Length*

47-50 in. (1194 - 1270 mm) depending on engine and installation.

- Construction

Wood - Built Up

- Pushrods

Preinstalled

- Pushrod Material

Steel Rods w/thread on both ends. Running in plastic guide tubes. Plain rod with EZ Connector & Z-Bend for Nose Gear Steering.  [Variable Length two piece rod for throttle w/thread on both ends.]

- Servo Tray

Pre-installed. Universal Adjustable for F/JR/Air/HiT

- Color

Red and white with blue & yellow trim, black lettering & gray rivets & panel lines. 

- Servos Needed?

1 Throttle, 1 Elevator, 1 Rudder

- Servo Locations

Tray Centre Inside Fuselage.

- Picture of Fuselage Cockpit as seen from left rear quarter.

Note Detailing on of pilots and instructment panel. 

 

- Picture of Fuselage as seen from right side.

More Pictures of Fuselage

HORIZONTAL STAB/ELEV

- Horiz Stab Span 21-7/8 in. (556 mm)

- Horiz Stab Area*

80 sq in. (516 sq cm)
- Horiz Stab Construction One Piece - Wood - Built Up

- Elevator Area

47 sq in. (303 sq cm) each. Two independent elevators.

- Elevator Construction

One Piece - Wood - Built Up

- Pre-Hinged

Yes. 6 Hinges.

- Hinges Factory Pinned? Yes. All elevator hinges are pinned. 4 pins per hinge inboard and outboard. 2 pins per hinge centre 4 hinges.

- Hinge Type

Real Hinge with Metal Pin.

- Airfoil

Slab.

- How Mount to Fuse?

Install into machined slot in fuselage and glue with 30 Minute Epoxy.

- Support Struts?

No. Not Required

- Color Top

Red and white with blue trim & gray rivets & panel lines. 

- Color Bottom

Red and white with blue trim & gray rivets & panel lines.

- Color Pattern Top vs Bottom

Same

- Picture of Horizontal Stabilizer and Elevator. Top and Bottom views are identical.

VERTICAL STAB/RUDDER

- Vertical Stab Area*

35 sq in. (226 sq cm)

- Rudder Area

23 sq in. (148 sq cm)

- Construction

Wood - Built Up

- Pre-Hinged

Yes. 3 Hinges.

- Hinges Factory Pinned? Yes. 4 pins per hinge top and bottom hinge. 

- Hinge Type

Real Hinge with Metal Pin

- Airfoil

Slab

- How Mount to Fuse?

Install into machined slot in fuselage and glue with 30 Minute Epoxy.

- Color

Red and white with blue trim, black lettering & gray rivets & panel lines. 
- Color Pattern Left vs Right Same
- Picture of Vertical Stabilizer and Rudder. Left and Right views are identical

COVERING

- "Sure Seal"

Thermal Shrink Film

- Self Adhesive

Low Temperature

- Patchable

Yes. Use patch sheet provided or aftermarket use Ultracote Plus or Ultracote Regular.

- Patch Sheet Provided?

Yes Red. Use Factory Patch Sheets if possible. Aftermarket covering will not match colors exactly. 

- Ultracote System Approx Color Match

Note: We recommend Ultracote Plus and a Heat GUN for patching using after market covering.  

Note: Color Names with * are poor matches to factory colors. 

Color UltraCote UltraCote Plus UltraTrim UltraPaint UltraStripe
Flame Red GOL-883 GOL-813 GOL-81300 GOL-P81390 na
White GOL-870 GOL-800 GOL-80000 GOL-P80090 na
Black GOL-874 GOL-804 GOL-80400 GOL-P80490 na
Gray GOL-882 GOL-812 na GOL-P81290 1/16 in. Silver GOL-81120
Deep Blue GOL-873 GOL-803 GOL-80300 GOL-P80390 na

 

LANDING GEAR

Trike

- Main Gear

5/32 in. (4 mm) steel wire pre-bent and chromed

- Stance - Between Wheels 13 in. (330 mm) between inboard side of wheels.

- Main Wheels

Two of 2-7/16 in. (62 mm) Ultralight Treaded.

- Main Wheel Pants na
- Wheels Pants made of? na
- Main Gear Struts? Yes. Scale like molded struts pre-installed over main gear wires. 
- Retract Ready? na
- Retracts that fit... na

- Nose Gear

5/32 in. (4 mm) Wire

- Nose Wheel

One of 2-7/16 in. (62  mm) Ultralight Treaded

- Nose Wheel Pants na
- Nose Wheel Pant made of? na
- Nose Gear Strut? Yes. Scale like molded strut pre-installed over nose gear wire. 

- Tail Wheel Assembly

na. Trike Gear

- Tail Wheel

na. Trike Gear

- Tail Wheel Steering Mechanism

na. Trike Gear

- Picture of Main Gear, Nose Gear, Clamps, Wheels, Wheel Collars, Gear Doors and  pre-mounted Struts as provided in hardware pack.
- Picture of strut assembly as pre-mounted on all three landing gear legs..

COWL

- included Yes with scale like exhaust stacks.
- material Fibreglass
- color True Red with black stacks.
- trim supplied Painted with Epoxy
- trim applied by? Factory
- Picture of Fibreglass Cowl from front and top. Note scale detailing of exhaust stack. Completely painted and ready to mount out of the box. 

ENGINE

Not included. See Options

- 2 cycle

.46-.60 cu in. (6.5-10cc). GMS-47PRO or Enya 50CX Recommended. For High Performance use GMS-61PRO or Enya 60XF4ALC

- 4 cycle

.53-.70cu in. (8-12 cc)

ENGINE MOUNT

T-bar Beams.  Aluminum Clamp Type all pretapped

- Firewall Predrilled for Mount?

No. To allow after market orientation of engine

- Predrilled orientation choices

Modellers choice

- Orientation Recommended

Modellers choice

- Mount Installed?

No. To allow after market orientation of engine

- Engine Lug Length - Max 1-5/8 in. (41 mm)
- Engine Width - Max Upright Mounting - 1-9/16 in. (39mm). Can be increased to approximatley 2-3/4 in. (70mm) by setting gap between aft fixed firewall and forward removable firewall to be 1/4 in. (6 mm) using hardware provided. 

Inverted - same as upright. Will require use of muffler extension for most engines to allow muffler to clear side of fuselage. 

45 or 135 or 225 degrees... approximately 2 in. (51mm) by setting gap between aft fixed firewall and forward removable firewall to be 1/4 in. (6 mm) using hardware provided. 

Note that T-beam engine mounts are normally utilized with clamp side towards head of engine. In some cases installation can be easier with one or both of the T-beams positioned so that the clamp side faces away from the engine head.  

- Beam Length 2-7/8 in. (73 mm) flat useable. 3-1/2 in. (89mm) from firewall to tips. 
- Picture of Engine Mount. Front View. Clamps can accomodate wide range of engine mounting lug sizes.

More Pictures of Engine Mount

- Power Module System

Yes. Fixed firewall aft. Removable firewall forward secured to aft firewall with mounting bolt system. Engine mounts, tank & engine mounted to removeable firewall.

- Picture of Power Module partially removed from fuselage showing forward removeable firewall with tank (right) and fuselage with aft fixed firewall and retaining studs (left).
- Picture of Engine Mounts and Engine Installed on forward removeable firewall prior to inserting power module into fuselage. Note Engine is at approx 195 degree rotation from upright.
More Pictures of Power Module

RADIO

Not included. See options

- 4 channels

Need 4 servos.

SERVO TRAY Preinstalled. Universal adjustable for F/JR/Air/HiT.
- Picture of Servo Tray with universally adjustable sliders highlighted in purple shading. Adjust to fit length of Futaba, Airtronics, JR or Hi-Tech standard servo. Tighten screws to lock slider into position. vma_servotray_withsliders copy2.jpg (36450 bytes)

More Pictures of Servo Tray & Linkages

FUEL TANK

- Type

Plastic

- Size

10.5 oz (300 cc)

- Clunk

Yes

- Silicone Tubing

No

- Metal Tubing

2 - Prebent & fitted in stopper

HARDWARE SET

Pictures of all Parts Bags Included with this Model.

WEIGHT

- Empty* - Assembled

4-1/4 - 4-3/4 lbs (1932 - 2158 g)

- Flying Dry* - 2 cycle

5-1/2 - 6 lbs (2500 - 2730 g)

- Flying Dry* - 4 cycle

6 - 6-1/2 lbs (2730 - 2950 g)

WING LOADING

- Empty* - Assembled

19.2 oz/sq ft @ 4-1/2 lbs

- Flying Dry* - 2 cycle

24.5 oz/sq ft @ 5-3/4 lbs

- Flying Dry* - 4 cycle

26.7 oz/sq ft @ 6-1/4 lbs

SET UP SPECS

- CG Location

3 to 3-1/2 in. (78-86 mm) back from the leading edge of the wing with the tank installed but empty. Ideally 3-1/4 (82 mm) back from leading edge of the wing with tank empty. CG is measured with the engine, tank, radio gear and all components installed but WITH NO FUEL IN THE TANK.
- Aileron Throw. (Use Low Rate for first flights and all training and/or if your radio does not support dual rates)
Aileron Movement Low Rate High Rate
 Left Up & Right Down 1/2 in. (12.5 mm) 3/4 in. (19 mm)
Left Down & Right Up 1/2 in. (12.5 mm) 3/4 in. (19 mm)
Total Throw from Up to Down. 1 in. (25 mm) 1-1/2 in. (38 mm)
- Rudder Throw at Widest section of Rudder. (Use Low Rate for first flights and all training and/or if your radio does not support dual rates)
Rudder Movement Low Rate High Rate
 Left 3/4 in. (19 mm) 1 in. (25 mm)
Right 3/4 in. (19 mm) 1 in. (25 mm)
Total Throw from Left to Right. 1-1/2 in. (38 mm) 2 in. (50 mm)
- Elevator Throw (Use Low Rate for first flights and all training and/or if your radio does not support dual rates)
Elevator Movement Low Rate High Rate
 Up 1/4 in. (6 mm) 3/4 in. (19 mm)
Down 1/4 in. (6 mm) 3/4 in. (19 mm)
Total Throw from Up to Down 1/2 in. (12 mm) 1-1/2 in. (38 mm)
- Flaps Throw   na
- Tailwheel Throw na. Trike Gear

- Engine  Horizontal Thrust Line

Factory line across front face of forward removable firewall. Approximately 1-3/4 in. (44 mm) down from top of fuselage at firewall. 

- Engine  Vertical Thrust Line Vertically up and down through centre of forward removeable firewall and lieing perpendicular to the horizontal thrust line. 

- Engine Thrust Angle.

None. 1-3 degrees of right thrust may assist with take offs but is not required. The power module system allows modellers to easily set any particular horizontal and/or vertical thrust at any time before or after assembly. 

SHIPPING BOX

- Cardboard

Brown

- Size Length x Width x Depth

43-3/16 x 13-11/16 x 8-9/16 in. (1096 x 348 x 217 mm)

- Length plus Girth

87-5/8 in. (2226 mm)

- Volume

2.93 cu ft (.0828 cu m)

- Weight with kit

11 lbs 7 oz (5199 g)
- Other Info na
SHIPPING INFO
- Shipping Method in Canada. Canpar most locations (enroute time 1-3 business days west,  5-10 business days east). Canada Post to remote  locations in the south and to YT, NWT, Nunavut in the north. 
- Shipping Method to USA lower 48 states FedEx Ground (enroute time 5-10 business days west, 10-14 business days east)
- Shipping method to Hawaii, USA, APO or USA possessions. United States Postal Service Priority Mail (enroute time approx 7 business days)
- Shippable outside Canada or USA by Air or Surface Mail? - No. Length plus Girth exceeds limit of 78.8 in (2 m) and/or Length exceeds limit of 39.4 in. (1 m)
- Shippable outside Canada or USA by Air or Surface Mail if separated into multiple boxes?  - No. Fuselage length exceeds length limit of 39.4 in. (1 m)  
- Shippable outside Canada or USA by Fedex? Yes. Refer to  www.fedex.com for quote to your location. Size, weight and location will be required. See box sizes and weights above. 

DISPLAY BOX

- Cardboard White
- Protected by Plastic Bag & Shipping Box
- Size Length x Width x Depth 42-3/16 x 13-3/16 x 8-1/16 in. (1072 x 335 x 205 mm)
- Length plus girth 84-3/4 in. (2152 mm)
- Volume 2.60 cu ft (.0733 cu m)
- Weight with kit & protective plastic bag. 9 lbs 7 oz (4290 g)
- Label covers all of Display Box 98% Coverage.
- Label front colors Colors = Four color process.Mainly white, red and blue. 
- Label front size 42-3/16 x 13-3/16 in. (1072 x 335 mm)
- Label front picture
- Label side panel colors Colors = Four color process.Mainly white, red and blue.
- Label side panel size 42-3/16 x 8-1/16 in. (1072 x 205 mm)
- Label left and right sides pictures

- Label end panel colors Colors = Four color process.Mainly white, red and blue.
- Label end panel size 13-3/16 x 8-1/16 in. (335 x 205 mm)
- Label end panel picture

* NOTES & LEGEND

- Accuracy of Dimensions Dimensions provided here are within +/- 3% in production.

- na

Not applicable this model

- blank data or information Not known at this time
- [info?] Estimated. Yet to be confirmed.

- Area* of Wing

Includes wing saddle area, ailerons & flaps where fitted.

- Area* of Horizontal Stab. Does not include area of elevator(s).
- Area* of Vertical Stabilizer Does not include area of rudder.

- Length* of Fuse

From Spinner back plate to Trailing Edge of Rudder

- Empty* Weight

No radio, engine or fuel

- Flying Dry* Weight

With radio, engine. No fuel

- Flying Dry* Loading

With radio, engine. No fuel

logoweb96small.gif (1626 bytes) 

©Richmond RC Supply Ltd. All Rights Reserved. Unauthorized commercial use strictly prohibited.
Prices, Specifications, Features and Availability subject to change without notice
Production Colors and Graphic Schemas may differ from that shown. 
Artwork, text and information for the use of consumers and Richmond RC customers only
For information contact webmaster@richmondrc.com

2001-05-12 21:51:10 Hit Counter

News, Sales, Promos!
Richmond RCSupplyStoreA Division of Richmond RC Supply Ltd.ZapGlueA Division of Richmond RC Supply Ltd. (604) 940-1066