| 1 | Part#: | VMA-T210WTH |
20070428 00010563 |
| 4 | Dimensions: | Please See Note |
20070425 00010567 |
| The dimensions of the Horizontal Stabilizer include the mounting Saddle and Elevator unless otherwise noted. The Elevator Quantity is the number of elevator segments. This is usually 1 or 2. i.e. 1 if the elevator is one piece, 2 if the elevator is split into a right and left segment. The Elevator Length is expressed as the length per elevator segment. The Elevator Area is expressed as the total of the area of all elevator segments. | |||
| 5 | Terminology: | Please See Note |
20070425 00010568 |
| The term "effective" is used to desribe the size of an object which is tapered or irregularly shaped. The term "chord" describes the linear distance from the leading edge to the trailing edge through a wing or control surface. The terms "saddle" and "saddle area" describe that portion of a flying surface such as the center section of a wing or horizontal stabilizer where it intersects the fuselage. | |||
| 8 | Horiz Stabilizer Location: | Horizontal Stabilizer slot in aft end of Fuselage |
20070425 00010571 |
| 21 | Horiz Stabilizer Airfoil Shape: | Slab |
20070425 00010584 |
| 28 | Horiz Stabilizer Material: | Balsa Wood & Light Plywood. Ribs, Formers and Sheeting are Laser Cut. Sticks, Stringers & Strips are Saw Cut. |
20070425 00010591 |
| 29 | Horiz Stabilizer Construction Method: | Built Up |
20070425 00010592 |
| 30 | Horiz Stabilizer Construction Adhesive: | PVA, Cyanoacrylate and Epoxy |
20070425 00010593 |
| 31 | Horiz Stabilizer Sheeted Fully: | No |
20070425 00010594 |
| 35 | Horiz Stabilizer Ribs Capped: | Yes |
20070425 00010598 |
| 36 | Horiz Stabilizer Attaches to Fuselage via: | Slot in Fuselage and Adhesive |
20070425 00010599 |
| 37 | Horiz Stabilizer Adhesive Required: | 30 Minute Epoxy |
20070425 00010600 |
| 38 | Horiz Stabilizer Requires Struts: | No |
20070425 00010601 |
| 39 | Horiz Stabilizer Elevator Factory Installed: | Yes |
20070425 00010602 |
| 40 | Horiz Stabilizer Elevator Quantity: | 1 (i.e. not split into left & right halves) |
20070425 00010603 |
| 49 | Horiz Stabilizer Elevator Hinge Type: | Flexible Live Low Gap |
20070425 00010612 |
| 50 | Horiz Stabilizer Elevator Hinge Adhesive: | Cyanoacrylate |
20070425 00010613 |
| 51 | Horiz Stabilizer Elevator Hinge Material: | Proprietary Super Strong |
20070425 00010614 |
| 52 | Horiz Stabilizer Elevator Hinges Pinned: | Yes, Inboard & Outboard |
20070425 00010615 |
| 53 | Horiz Stabilizer Elevator Servo Required: | Yes 1 Sub-Micro |
20070425 00010616 |
| 54 | Horiz Stabilizer Elevator Servo Location: | Exterior right side of fuselage near the tail |
20070425 00010617 |
| 55 | Horiz Stabilizer Elevator Servo Mounting Method: | Tray (Wood) |
20070425 00010618 |