Product Information
PRODUCT INFORMATION
 
 
VMA-C210YW
VMAR J3 CUB 09-15 ARF ECS - WING SET - YELLOW
 
 



1 Part#: VMA-C210YW   20070511
00012248
2 Dimensions: Please See Note   20070505
00012249
The dimensions of the Wing include the mounting Saddle plus any Ailerons, Flaperons, Flaps or other control surfaces unless otherwise noted. The Aileron Quantity is the number of aileron segments. This is usually 2 with one aileron on the right wing panel plus one aileron on the left wing panel. The Aileron Length is expressed as the length per aileron segment. The Aileron Area is expressed as the total of the area of all aileron segments. Flaperons by design have the same specifications as ailerons. Flap dimensions are denoted in the same manner as ailerons. Flap Quantity is usually 2 (one on the left wing panel plus one on the right wing panel). Flap Length is the length of each flap segment and Flap Area is expressed as the total of the area of all flap segments.
3 Terminology: Please See Note   20070505
00012250
The term "effective" is used to desribe the size of an object which is tapered or irregularly shaped. The term "chord" describes the linear distance from the leading edge to the trailing edge through a wing or control surface. The terms "saddle" and "saddle area" describe that portion of a flying surface such as the center section of a wing or horizontal stabilizer where it intersects the fuselage.
6 Wing Location: Above Fuselage   20070505
00012253
7 Wing Span Tip to Tip: 54.33 in. (1380 mm)   20070503
00012254
8 Wing Span (effective): 50.39 in. (1280 mm)   20070503
00012255
9 Wing Chord at Root: 7.83 in. (199 mm). Not considering center notch   20070505
00012256
10 Wing Chord at outboard end of Aileron: 7.83 in. (199 mm)   20070503
00012257
11 Wing Chord (effective): 7.83 in. (199 mm)   20070505
00012258
12 Wing Area: 394.82 sq in. (2547.20 sq cm)   20070506
00012259
13 Wing Width of Saddle: 3.54 in. (90 mm)   20070503
00012260
14 Wing Length of Saddle: 7.09 in. (180 mm)   20070503
00012261
15 Wing Area of Saddle only: 25.11 sq in. (162.00 sq cm)   20070503
00012262
16 Wing Area without Saddle: 369.71 sq in. (2385.20 sq cm)   20070506
00012263
17 Wing Airfoil Shape: Flat Bottom   20070503
00012264
19 Wing Dihedral at Center: 1.5 degrees   20070503
00012266
21 Wing Taper along Leading Edge: None   20070503
00012268
22 Wing Taper along Trailing Edge: None   20070503
00012269
23 Wing Thickness Maximum: .87 in. (22 mm)   20070503
00012270
24 Wing Material: Balsa Wood & Light Plywood. Ribs, Formers and Sheeting are Laser Cut. Sticks, Stringers & Strips are Saw Cut.   20070503
00012271
25 Wing Construction Method: Built Up   20070503
00012272
26 Wing Construction Adhesive: PVA, Cyanoacrylate and Epoxy   20070503
00012273
27 Wing Sheeted Fully: No   20070503
00012274
28 Wing Sheeted Center Section: 7.48 in. (190 mm)   20070503
00012275
29 Wing Sheeted Leading Edge: 1.97 in. (50 mm)   20070503
00012276
30 Wing Sheeted Trailing Edge: 1.457 in. (37 mm)   20070503
00012277
31 Wing Ribs Capped: Yes   20070503
00012278
32 Wing Plugs In to Fuselage: No   20070503
00012279
33 Wing Front attaches to Fuselage with: Leading Edge Dowel   20070503
00012280
34 Wing Back attaches to Fuselage with: 2 metal bolts   20070503
00012281
35 Wing Requires Struts: Yes   20070503
00012282
36 Wing Spar Joiner Quantity: 1 (Please See Note)   20070503
00012283
In some markets the wing halves have been joined by the factory and the wing then shipped in one piece. Where a one piece wing has been supplied, the individual wing halves, wing spar joiner(s), alignment pins, center joint trim tape and other components used to join wing halves together have already been incorporated by the factory into the one piece wing.
37 Wing Spar Joiner Material: Plywood   20070503
00012284
38 Wing Spar Joiner Length: 7.24 in. (184 mm)   20070503
00012285
39 Wing Spar Joiner Width: .669 in. (17 mm)   20070503
00012286
40 Wing Spar Joiner Thickness: .173 in. (4.4 mm)   20070503
00012287
46 Wing Joint Adhesive: 30 Minute Epoxy   20070505
00012293
47 Wing Joint Trim Tape: Yes Clear   20070505
00012294
48 Wing Ailerons Factory Installed: Yes   20070505
00012295
49 Wing Ailerons Quantity: 2   20070505
00012296
50 Wing Aileron Type: Strip (2)   20070505
00012297
51 Wing Aileron Length per Aileron (effective): 19.13 in. (486 mm)   20070503
00012298
52 Wing Aileron Chord (effective): .945 in. (24 mm)   20070503
00012299
Wing Aileron Chord tapers from 24 mm at the inboard end (closest to the fuselage) to 24 mm at the outboard end.
53 Wing Aileron Area: 36.16 sq in. (233 sq cm)   20070503
00012300
54 Wing Aileron Area relative to Wing Area: 9.16 %   20070506
00012301
55 Wing Aileron Area relative to Wing Area without wing saddle: 9.78 %   20070506
00012302
56 Wing Aileron Hinges per Aileron: 4   20070503
00012303
57 Wing Aileron Hinge Type: Flexible Live Low Gap   20070503
00012304
58 Wing Aileron Hinge Material: Proprietary Super Strong   20070503
00012305
59 Wing Aileron Hinge Adhesive: Cyanoacrylate   20070503
00012306
61 Wing Aileron Servo Required: Yes 2 Sub-micro   20070503
00012308
62 Wing Aileron Servo Location: Outboard in bottom of each wing half   20070503
00012309
63 Wing Aileron Servo Rails: Yes in Servo Cavity   20070503
00012310
65 Wing Aileron Servo Wiring Tube: Yes   20070505
00012312
66 Wing Ailerons Flaperon Ready with Computer Radio: Yes   20070505
00012313
67 Wing Flaps Factory Installed: No   20070505
00012314
87 Wing Color Top Schema: Monochrome except for black registration N5730C   20070505
00012334
88 Wing Color Top Main: Yellow   20070503
00012335
89 Wing Color Top Trim: Black   20070503
00012336
92 Wing Color Top vs Bottom: Similar   20070503
00012339
93 Wing Color Bottom Schema: Monochrome except for black registration N5730C   20070505
00012340
94 Wing Color Bottom Main: Yellow   20070503
00012341
95 Wing Color Bottom Trim: Black   20070503
00012342
98 Wing Weight: .52 lbs (235 g). Please See Note   20070503
00012345
The weight of the Wing is as it was when it is removed from the shipping box. This weight does NOT include the weight associated with any adhesives, spar joiners or other weight associated with end user assembly.

20120830 03:56:57 PST. Subject to Change Without Notice.
Copyright Richmond RC Supply Ltd. VMA-C210YW_spec.htm